10TPH 20TPH Secondary Jaw Crusher Industrial Handling Equipment
Introduction of Secondary Jaw Crusher
Secondary Jaw Crusher, whose reduction ratio up to 4-6 and the
finished products are even, can be widely used in breaking hard,
medium-hard, soft ore, such as various kinds of ore, the solvent,
slag, building stones, marble, etc. compression strength does not
exceed 320Pa.
Applicable Scope of Secondary Jaw Crusher
Fier jaw crusher is widely used in mining, smelting, building
materials, highway, railway, water conservancy and chemical
industry, etc.
Small jaw crusher Suitable for crushing all kinds of materials with
compressive strength not exceeding 320 Mpa.
1. Mainly used in metallurgy, mining, chemical industry, cement,
construction, refractory materials and ceramics, etc.
2. Mainly used for breaking various rocks, suitable for crushing
ores, river pebbles, limestone, slag, basalt, granite, and other
materials whose compressive strength is not higher than 320Mpa.
FIER Jaw crusher size and capacity as follow:
Model | Material size(mm) | Destrage size(mm) | Outpurt(t/h) | Power(kw) | Weight(t) | Size |
FMP150x250 | 125 | 10-40 | 1-3 | 5.5 | 0.8 | 720x660x850 |
FMP200x300 | 180 | 15-50 | 2-6 | 7.5 | 1.2 | 910x750x990 |
FMP200x350 | 180 | 18-70 | 3-10 | 11 | 1.5 | 1000x870x990 |
FMP250×400 | 210 | 20-60 | 5-20 | 15 | 2.8 | 1300×1090×1270 |
FMP400×600 | 340 | 40-100 | 16-60 | 30 | 7 | 1730×1730×1630 |
FMP500×750 | 425 | 50-100 | 40-110 | 55 | 12 | 1980×2080×1870 |
FMP600×900 | 500 | 65-160 | 90-180 | 55 | 17 | 2190×2206×2300 |
FMP750×1060 | 630 | 80-140 | 110-320 | 110 | 29 | 2660×2430×2800 |
FMP800×1060 | 640 | 80-150 | 130-330 | 110 | 29.8 | 2710×2430×2800 |
FMP900×1060 | 685 | 80-150 | 230-390 | 110 | 33 | 2870×2420×2940 |
FMP900×1200 | 750 | 95-165 | 220-450 | 110-132 | 58 | 3380×2870×3330 |
FMP1000×1200 | 850 | 195-265 | 315-500 | 110-160 | 69 | 3480×2876×333 |
FMP1200×1500 | 1020 | 150-300 | 400-800 | 160-220 | 100.9 | 4200×3300×3500 |
Working principle of FIER jaw crusher Wikipedia
The crushing mode of FIER jaw crusher is flexural extrusion type.
1. The motor drives the belt and pulley, which move the jaw up and
down through an eccentric shaft.
2. When the movable jaw rises, the Angle between the bracket and
the movable jaw increases, thus pushing the movable jaw towards the
fixed jaw.
At the same time, the material is crushed, rubbed, crushed, and so
on.
3. When the movable jaw descends, the Angle between the bracket and
the movable jaw becomes smaller, and the movable jaw leaves the
fixed jaw under the action of pull rod and spring.
4. At this time, the broken material is discharged from the lower
mouth of the crushing chamber. With the continuous rotation of the
motor, the broken motor jaw is used for periodic crushing and
discharging to achieve mass production.
Types of Fier Jaw crusher
Fier jaw crusher is the leader of the crusher machine.
1. According to the size type of materials, it can be divided into
coarse jaw crusher and thin jaw crusher.
The coarse type is the crushing of large materials into small ones.
Fier thin jaw crusher is mainly broken stone cobble.
2. According to the frame structure, the FIER Jaw crusher is
divided into two types: welded type and assembled type.
Small and medium-sized specifications generally use welding type,
large specifications generally use assembly type.
The welding type has the characteristics of impact resistance,
uniform stress, and low failure rate.
Assembly type jaw crusher Equipped with advanced modular, weldless
frame structure design, fatigue strength, high reliability, and the
whole machine equipped with design, transport, installation is more
convenient, especially suitable for underground mines,
high-altitude mines, and other small, difficult places to install.
3. According to whether there is electricity, it can be divided
into the electric type and diesel type
The power type has a wide range of use.
The diesel-powered type is used in areas where electricity is
inconvenient.
4. Mobile jaw crusher and stationary crusher machine
Why us?
1. Complete stone production line, the Crusher near to turn-key
project;
2. Stationary type or mobile type for choosing
3. First class workmanship.Reliable quality with CE approved,
reaching to European standard
4. Updating in design and function year by year, Invention
technical patent. Forms our own unique design by considering of
saving more cost and improve the processing capacity for user’s
consideration.
